5W High Power LED, Pure Blue Light & Efficient Curing
Adopting 5W high-power pure blue light LED, the equipment outputs pure blue light in the wavelength range of 385nm to 515nm, which greatly improves the curing efficiency of photosensitive materials. Pure blue light not only penetrates deep into the material, but also cures each layer quickly and uniformly, reducing the risk of thermal shrinkage effects on the material. With high brightness and a wavelength range suitable for curing, the device improves curing speed while ensuring material stability and strength.
High-Capacity Battery & Long Standby Time
The device has a built-in 2200mAh high-capacity Li-ion battery, which provides long battery life. The device supports up to 90 days of standby time under full charge, providing long-lasting battery life even under high-frequency use. Doctors do not need to recharge frequently, which ensures consistent workflow and long-term efficient operation of the device, reduces the risk of device downtime due to battery problems, and improves work efficiency.
Automatic Standby & Intelligent Shutdown Function
The device is equipped with intelligent automatic standby and shutdown function, when it is not used within the specified time, it will automatically enter standby mode; no operation within 20 seconds will automatically shutdown to avoid unnecessary battery consumption. Intelligent shutdown not only provides ease of operation, but also extends the life of the device. This design ensures less energy loss when the device is not in use, making it more in line with the intelligent needs of modern medical devices.
Fast Curing Functions & Long Life
The device has an efficient one-second cure function and can support more than 500 consecutive uses per charge to meet frequent medical curing needs. Each operation takes only 1 second, making it ideal for situations where curing needs to be done efficiently, reducing operation time and achieving high quality curing results in a short period of time. For hospitals or clinics, the long battery life means that the device will continue to perform at its best throughout the day, reducing the inconvenience of waiting for recharging and providing a more efficient experience for both healthcare professionals and patients.
|
Parameters
|
|
Dimensions
|
Φ72mm*275mm
|
|
Net weight
|
255g
|
|
Host input
|
(Charging state) DC5V 1A
(Working state) 3.6V
|
|
Power adapter
|
(Input) 100-240VAC 50Hz/60Hz 0.4A Max
(Output) DC 5V/1A
|
|
LED performance
|
5W high-power blue LED light
|
|
Wavelength
|
385nm-515nm
|
|
Mode and time setting
|
P1 (high light intensity mode) time can be set to 1 second, 3 seconds;
P2 (standard mode) time can be set to 5 seconds, 10 seconds, 15 seconds, 20 seconds
|
Operation Method:
1. Press the power switch button (‘I’) to switch on the machine.
2. Mode setting: gently press the mode setting button ( ‘ M ’ ) to change the operation mode, the light curing machine will work in the set mode to irradiate different intensity of blue light, the available modes are shown in Table 1.
3. Time setting: gently press the time setting key ( ‘ T ’ ) to set the curing time. See Table 1 for the curing time that can be set.
4. When using, put the disposable film sleeve into the head of the main unit.
5. Then align the front connector light source to the position to be cured, press the power switch button (‘ I “), the host issued a ”tick’ sound, the host sends out a blue light and work according to the selected mode of operation, the digital display from the selected timing time to start showing the countdown time, the timing to 0 when the end of the work, the digital display returns to show the set timing time.
6. Press the power switch button (’ I ’) can end the work at any time to turn off the output before the timing time is finished after normal use.
7. At the end of an irradiation cycle, you can immediately press the power switch button ( ‘ I ’ ) to start the next irradiation cycle, such as the obvious feeling that the handle began to get hot should stop working until the handle is completely cooled down and then begin to work again, it is recommended that the number of consecutive irradiation is not more than 10 times.
8. Low voltage indication: the host has an internal battery low battery detection function, when the battery is detected low battery, the digital tube flashes, then please charge in time.
9. After use, if the transparent cover is stained with resin, please use a cotton cloth to wipe clean, so as not to affect the light intensity.
10. The machine will automatically switch off after 2 minutes of inactivity. To switch on the machine, please press ON / OFF.
11. The effective light intensity of this machine is many times higher than that of halogen lamp light curing machine, and the curing depth of light curing composite resin is not less than 4mm in 10 seconds.
12. The front connector of the front end can be removed, but it can't be sterilised by autoclaving, otherwise it will lead to damage.
13. When the equipment is used continuously for a long time, the maximum temperature of its application part of the front connector out of the light end can reach 56 ℃, so after 100 seconds of continuous use of the equipment, it should take a break for 10 minutes to avoid too long irradiation, or in the feeling that the temperature rises significantly, stop using the equipment.
Trouble Removal:
|
Failure State
|
Possible Cause
|
Handling Method
|
|
No Indication, No action
|
1. the battery in the light curing machine has no electricity
2. The battery is damaged
3. Host battery protection
|
1. Connect to the power supply to charge/replace the battery
2. Replace the battery
3. Place on the charging stand to charge and activate
|
|
Underlight
|
Resin residue on the front end of the transparent cover
|
1. Remove residual resin
2. Replace transparent cover
|
|
No charge after connecting to the power adapter
|
1. It is not plugged in
2. The power supply is damaged or the specifications do not match
3. The charging socket contact plug has impurities
|
1. Plug out and reconnect
2. Replace the original adapter
3. Wipe the charging socket contact plug with alcohol
|
|
Battery life becomes shorter after charging
|
Smaller battery capacity
|
Replace battery
|
|
The nixie blinks in charging mode
|
The battery voltage is too low
|
Charge 15 minutes automatically restore to normal state
|
Attention:
General Use
Professional Use Only: This product is for hospitals and dental clinics, operated by trained, qualified dentists or technicians with protective gear (goggles, masks) to prevent infection.
Reusable Product: Use a disposable isolation sleeve on the connector to avoid contact with patient skin or oral tissue. After each use, dispose of the sleeve per regulations and clean the connector’s surface with water or disinfectant.
Operation
Direct Light Positioning: Ensure the light source is aimed directly at the resin for effective curing.
Protective Shield: Use the original manufacturer’s protective shade to shield eyes from blue light.
Charging and Battery Care
Approved Charger: Use only the original charger to avoid damage to the battery and control circuits. Charge fully for 4 hours before first use.
Charging Precautions: Do not use the device while charging, and avoid leaving the charger connected long-term after charging completes.
No Conductors in Charging Socket: Avoid inserting metal objects in the charging socket to prevent short-circuits.
Charge in Cool, Ventilated Areas: Ensure proper contact between the device and charging base for effective charging.
Battery Handling: Do not open, shake, or short-circuit the battery, and avoid contact with metal objects.
Safety and Disposal
Electromagnetic Interference: Avoid using near electronic surgical equipment and in high-interference areas.
Environmentally Safe Disposal: Dispose of the product and battery following medical waste regulations.
